風機減震器在風機上的重要作用The important role of fan shock absorber in fan

    風機在工廠生產與日常日子中已經廣泛運用，但是有時咱們會發現設備在家裏或工廠裏的風機工作時，會由於風機的機械轟動和離心風機高速工作產生很大的噪聲。這些噪聲不光影響周圍的環境，並且還會形成必定的。

Fan has been widely used in factory production and daily life, but sometimes we will find that when the fan works at home or in the factory, it will produce a lot of noise due to the mechanical shock of the fan and the high-speed operation of the centrifugal fan. These noises not only affect the surrounding environment, but also form a certain amount.

    因此，有必要解決高速運轉時風扇的感覺和噪聲問題。進口風機減震器能有效地解決上述問題，目前在中國市場很受企業用戶歡迎。設備風機的減震器，面對風機感覺帶來的各種問題，采用減震器將風機與地面隔離。減震器能有效地防止風機的感覺傳播到地面，防止感覺的來源，進而起到降低感覺的作用。

TheREfore, it is necessary to solve the problem of the feeling and noise of the fan when running at high speed. The imported fan shock absorber can effectively solve the above problems, and is very popular in the Chinese market. The shock absorber of equipment fan is used to isolate the fan from the ground in the fACE of various problems caused by fan feeling. The shock absorber can effectively prevent the feeling of the fan from spreading to the ground, prevent the source of the feeling, and then reduce the feeling.

    風機減震器的主要原材料一般分為特殊增強尼龍和球墨鑄鐵。特別增強的尼龍原料是尼龍增強纖維，強度高；尼龍原料能耐酸堿，抗紫外線，並經過嚴格的老化試驗。

The main raw materials of fan shock absorber are generally divided into special reinforced nylon and ductile iron. Specially reinforced nylon material is nylon reinforced fiber with high strength; nylon material is acid and alkali resistant, UV resistant, and has undergone strict aging test.

    質量優良，安全性高。球墨鑄鐵經熱鍍鋅處理後具有良好的耐候性。重量輕，堅固，安裝方便，適用於各種機械減震器。彈簧經過熱處理、ED防鏽、烤漆等工序處理。25 mm和40 mm的荷載偏斜可以有效地消除機械結構的攪拌。尼龍原料的工作溫度為0~50攝氏度，風機減震器的通用設備在減震板下和風機鋼支架下製造。減震板為鋼筋混凝土板。使板下多風扇減震器受力均勻。減震器應根據風機的風量確定設備數量，一般不少於4台。

Good quality and high safety. Ductile iron has good weather resistance after hot dip galvanizing. Light weight, strong, easy to install, suitable for all kinds of mechanical shock absorbers. The spring is treated by heat treatment, ed antirust and baking paint. The load deflection of 25 mm and 40 mm can effectively eliminate the mixing of mechanical structure. The working temperature of nylon raw material is 0 ~ 50 ℃. The general equipment of fan shock absorber is manufactured under the damping plate and fan steel support. The damping plate is reinforced concrete slab. The force of multi fan shock absorber under the plate is uniform. The number of shock absorbers shall be determined according to the air volume of fans, generally no less than 4.

    通過動力計算，確定了風機減震器的選用要求。不得隨意更改風機擋板的數量和型號規格。采用風機減震器對風機機組進行減振，可以達到高效的減震效果，滿足降噪要求。在選擇質量比時，應注意避免同震，不必同時選擇較大的質量比。

Through dynamic calculation, the selection requirements of fan shock absorber are determined. It is not allowed to change the quantity, model and specification of fan baffle at will. Using the fan damper to reduce the vibration of the fan unit can achieve high-efficiency damping effect and meet the requirements of noise reduction. When selecting the mass ratio, it is necessary to avoid coseismic and to choose a larger mass ratio at the same time.